600/1000 v concentric cable solid stranded aluminum conductor PVC insulated electric power cable

 1. SCOPE
This specification is for PVC insulated single phase concentric cables with circular
stranded Aluminum conductors for operation up to and including 1000 Volts between
phases and 600 Volts to earth. The cable shall have a central phase conductor insulated
with red PVC and concentric layer comprising bare aluminum wires (combined
neutral-earth conductor) and out sheath in black PVC.
2. REFERENCES
The following standard contains provisions which, through reference in this text
constitute provisions of this specification. Unless otherwise stated, the latest editions
(including amendments) apply.
ISO 9001: Quality Management System-Requirements
ISO/IEC 17025: General requirements for the competence of testing and calibration
laboratories.
KS 04-1022:- Kenya Standard Specification for 600/1000V PVC-insulated single-phase
concentric cables with copper or aluminum conductors for electricity
supply.
3. MATERIAL AND CONSTRUCTION
3.1. The cable shall be designed and manufactured in accordance with Kenya Standard
KS 04-1022 and the requirements of this specification.
3.2. Phase Conductor
3.2.1 The phase conductor shall be circular stranded annealed Aluminum conductors
(class 2) as specified in KS 04-1022. The phase conductor shall have a left-hand direction
of lay.
3.2.2 The insulation of the phase conductor shall be red PVC compound specified in KS
04-1022. It shall be applied by an extrusion process and shall be spark tested in
accordance with KS 04-1022.
3.2.3 The thickness of insulation, determined in accordance with KS 04-1022, shall be not
less than the value given in Table 2 of this specification and the smallest of the measured
values shall not fall below the value given in the said table by more than (10% + 0.1mm).

resistance of the neutral conductor shall comply with Table 2 of this specification.
3.3.2 The concentric layer shall be applied with a right hand direction of lay.
3.4. Oversheath
3.4.1 The oversheath shall be an extruded layer of black PVC compound as specified in
KS 04-1022. The oversheath shall be spark tested in accordance with KS 04-1022.
3.4.2 The minimum thickness of the oversheath shall not fall below the value given in
Table 2 of this specification by an amount more than (15% + 0.1mm).
4 .STANDARD SIZES AND CHARACTERISTICS
The characteristics of the cables shall comply with table 2.

Table 2: Characteristics (as per KS 04-1022)

 Contact me

Contact us

SCG(Sanhe Cable Group)

Our trading company's name is sanhe cable, wholly-owned factory is called sitong cable.

1. What kinds of products does Sitong CABLE manufacture?
1)Bare Conductor ,such as AAC,AAAC,ACSR,ACAR,AACSR,ACSR/AW and so on;
2)Aerial Bundled Cable (1kV-35kV ),such as Duplex,Triplex,Quadruplex Drop Wires and so on;
3)PVC Insulated (Flexible ) Wire ;
4) PVC Insulated and Sheathed (Armoured) Power Cable;
5)Low, Medium, High Voltage (1kV-220kV) XLPE Insulated (Armoured) Power Cable;
6)Welding Cable, Control Cable, Concentric Cable, Rubber Sheathed Cable and so on.

2.Which markets do you involve mainly in?
Our products have been exported mainly to Australia, Russia, Africa, Middle East, South-east Asia, South America,Central America,North America, Europe ,Austrapa, etc.

3. Which standards do you comply with when you produce the electrical wires and cables ?
We are able to produce electrical wires and cables based on GB, JB, IEC, BS, DIN, ASTM, JIS, NF, AS/NZS, CSA, etc. Meanwhile, we can design and manufacture the cables according to the samples and technical specification the customer provided.

4. What is the min.order quantity ?
It depends on the type and size of electrical wires and cables. For some small electrical wires, 100 meters can be accepted .But for the power cables with medium or high voltage, that should comply with the property of installed equipments. Anyhow,we will try our best to solve the problem and meet with the requirement If you have special request.

1.100% all material must be tested.

2.All semi-finished products must be tested before entering the next process.

3.All finished products must be tested before packaging.

4.Commissioned by the authority of the third-party certification testing company for sampling.

 Contact Us

1) Packing length:100 to 1,000m reeled in carton drum or                   according to customers' requirement.
2) Outer packing: wooden case, carton box.
3) Other packing requirement according to client's request.

Contact Me