Factory Supply  CU/ XLPE /PVC DST Steel Tape Armad Cable Price 25 mm  

 

 

 

0.6/1kV copper conductor cu xlpe dst pvc cable

xlpe dst pvc cable Specification:

1. Rated Voltage : 0.6/1KV
2. Test Voltage: 4000V
3. Type of insulation : XLPE / PVC
4. Core : 1 core, 2core, 3 core, 3+1core, 4core, 3+2core, 4+1core, 5core.
5. Armoured : Armoured (Steel tape)
6. Material conductor : Copper / Aluminum
7. System : 1.2kv Earthed
8. Material : Stranded copper / Aluminum
9. Shape of conductor : sector
10. Size of conductor : 25-400 sq.mm
11. Length of cable : 3,000 meter

xlpe dst pvc cable Standard:

GB/T12706.1-2002 Cable for rated voltage for 1kv(Um=1.2kv) and 3kv(Um=3.6kv)

 

xlpe dst pvc cable Application:

This product is applicable to being fixedly lad on the transmission and distribution line of AC voltage rating 50HZ and rated voltage 0.6/1KV with the use for power transmission.

 

xlpe dst pvc cable Characteristic & use:

The maximum assigned temperature of the cable conductor is 90°c.

During having a short circuit (lasting less than 5 seconds) the maximum temperature of the cable conductor shall not be above be 250°c, the overloaded temperature shall not be above 130°c.

During the cable laying, the ambient temperature must be above 0°c,The minimum bending diameter must be above the following standard: single core cable  20D(mm)    multiple core cable  15D(mm)  D–practical external diameter of cable.

 

Specification of product

 

 

Steel wire armoured xlpe cable, commonly abbreviated as xlpe dst pvc cable, is a hard-wearing power cable designed for the supply of mains electricity. It is one of a number of armoured electrical cables – which include 11kV cable and 33kV cable – and is found in underground systems, power networks and cable ducting.

 

The typical construction of an xlpe dst pvc cable can be broken down as follows:

• Conductor: consists of plain stranded copper (cables are classified to indicate the degree of flexibility. Class 2 refers to rigid stranded copper conductors as stipulated by British Standard BS EN 60228:2005)
• Insulation: Cross-linked polyethylene (XLPE) is used in a number of power cables including BS5467 cable because it has good water resistance and excellent electrical properties. Insulation in cables like SWA armoured xlpe cable BS5467 ensures that conductors and other metal substances do not come into contact with each other.
• Bedding: Polyvinyl chloride (PVC) bedding is used to provide a protective boundary between inner and outer layers of the xlpe cable .
• Armour: Steel wire armour provides mechanical protection, which means the cable can withstand higher stresses, be buried directly and used in external or underground projects. The armouring is normally connected to earth and can sometimes be used as the circuit protective conductor ("earth wire") for the equipment supplied by cable.
• Sheath: a black PVC sheath holds all components of the cable together and provides additional protection from external stresses.

xlpe dst pvc cable Core Identification

 

FAQ:

1. Why use xlpe dst pvc cable?

With its steel wire armour, xlpe dst pvc cable is particularly useful in external or underground projects. As well as providing effective mechanical protection, the armour enables it to withstand higher pulling loads.

SWA’s XLPE (Cross-Linked Polyethylene) insulation is resistant to a wide range of chemicals and has good thermal stability.

Steel Wire Armoured BS5467 Cable is a robust and hard-wearing power cable with copper conductors, XLPE insulation, steel wire armour and a black PVC sheath. It is designed for the supply of mains electricity – for power networks, underground systems and in cable ducting – and is suitable for both indoor and outdoor use.

 

2. Which industries use xlpe dst pvc cable?

The versatile steel wire armoured BS5467 Cable is commonly used across a whole range of industries including building and construction, and rail and transport. The armoured mains cable is also supplied for transmission, distribution and power networks as well as automation and process control systems.

 

3. What is the difference between AWA and xlpe dst pvc cable?

Aluminium Wire Armour (AWA) is used in single core cable because it is non-magnetic. When an electric current passes through a cable it produces a magnetic field (the higher the voltage the bigger the field). The magnetic field will induce an electric current in steel armour (eddy currents), which can cause overheating in AC systems. The non-magnetic aluminium armour prevents this from happening. Both AWA and Steel wire armoured cables meet the requirements of BS5467.

 

4. When would I need to use Low Smoke Zero Halogen (LS0H) Steel wire armoured cable (BS6724)?

The Low Smoke Zero Halogen (LS0H) xlpe dst pvc cable is recommended for use in public areas. When exposed to fire, the LS0H sheath emits very low levels of smoke and non-toxic levels of halogen gas (typically under 0.5% HCl emission). LS0H may also be referred to as LSHF (Low Smoke Halogen Free), 0HLS (Zero Halogen Low Smoke), LSZH (Low Smoke Zero Halogen) or HFFR (Halogen Free Flame Retardant).

 

5. Can the wire armouring be used as an earth?

The wire armouring is not advised to be used as an earth. Although it is possible on cable up to a certain size, it should only be used as an additional earth. The armour should, however always be earthed at the supply end to ensure that it cannot become a live cable if the cable is severed or if a fault develops within the cable.

Steel wire armoured cable can be referred to more generally as mains cable, armoured cable, power cable and booklet armoured cable, BS5467 Cable.

 

FURTHER INFORMATION – SWA CABLE

We sell a large range of steel wire armoured cable, so if you cannot find the cable you require, please contact our Sales Team on WhatsApp: 86-15838290725 or Skype ID: xinyuanyy for further information and assistance.

Hongda Cable are based on the Wuzhi Industrial Estate near Zhengzhou China, so if you'd prefer to pick up your cable as opposed to having it delivered, please feel free to do so.

 

 

Our service

we are one of the biggest manufacture in china mainland. We will give you a perfect shopping experience . If you need visit our factory , we will meet you at the airport or train station.

Also we can offer other service 

Custom Merchandise:we can make cable as your need include the color ,size and so on.we also offer OEM .

Complete Course Tracking:we can offer you the service from the business begin to you get the cable and use it .

 

 

These cables are used for electricity supply in low voltage installation system, They are suitable for installation in indoors and outdoors, in cable ducts, under ground, in power and switching stations, local energy distributions, industrial plants, where there is no risk of mechanical damage.

 Construction

Conductors

The conductors shall be either of Class 1 or Class 2 of plain or metal-coated annealed copper or of plain aluminium or aluminium alloy, or of Class 5 of plain or metal-coated copper in accordance with IEC 60228.

Insulation

PVC Insulation material and thickness shall be as per IEC 60502-1, PVC material shall be Type A as per IEC 60502-1.

Colour Code

Colour Code (1)

Colour Code (2)

Other colours can be manufactured upon request.

Assembly / Inner Covering

The inner coverings may be extruded or lapped. For cables with circular cores, except cables with more than five cores, a lapped inner covering shall be permitted only if the interstices between the cores are substantially filled. A suitable binder is permitted before application of an extruded inner covering. The materials used for inner coverings and fillers shall be suitable for the operating temperature of the cable and compatible with the insulating material.For halogen free cables, the inner covering and fillers shall also be halogen free compound.

Armour

Aluminum/galvanized steel/steel wires applied helically over the Inner Covering as per IEC 60502-1, or double aluminum/steel tapes and copper/tinned copper wire can also be manufactured upon request.

Outer Sheath

Outer sheath shall be of extruded PVC Type ST1/ST2 as per IEC 60502-1, Polyethylene type ST3/ST7, Halogen free compound ST8, Polychloroprene, chlorosulfonated polyethylene or similar polymers, type SE1 are also available on request.

Fire Performance of Cable Sheaths

Cables can be supplied with special flame retardant PVC outer sheath to comply with the flame test requirements of IEC 60332-3-22, IEC 60332-3-23 and IEC 60332-3-24, Halogen Free material comply to IEC60754-1/2 and IEC 60684-2.