Picture for   xlpe/pvc cable 4mm2 copper conductor 4 core power cable

 

 

 

 

 

PVC power cables (plastic power cable) is one of high quality products of our company. The product not only has good electric capability, but also has good chemical stabilization, simple structure, easy to use, and the laying of cable do not be limited by the fall. It is widely used at the transformer circuit which rated voltage is 600V or under.

The product can be produced against the standard of IEC60502 and IEC60331, BS 6346, DIN VDE 0271, and the standard required by the clients.

1. The long-term permissible operation temperature of the conductor shall not be higher than 70

2. The max temperature of the conductor of cable should less than 160 when short circuit. (less than 5 second)

3. The cable is not limited by drop in level when being laid, and the environment temperature shall not be lower than 0

4. Perfect chemical stability, resistant against acids, alkalis, grease and organic solvents, and flame retardant.

5. Light weight, perfect bending properties, installed and maintained easily and conveniently

 

 

 

Specifications for xlpe/pvc cable 4mm2 copper conductor 4 core power cable  

 

 

Applications for xlpe/pvc cable 4mm2 copper conductor 4 core power cable  

 

It applies to electrical power transmission and distribution lines with AC rated voltage U0/U up to and including 0.6/1 kV. For outdoor and indoor installation in damp and wet locations, laid directly in the ground where

excessive mechanical stresses are present in sloping and moving terrains and in vertical or inclined laying, as well as in locations susceptible to sliding.

 

 

 

Inspection Quality System for  xlpe/pvc cable 4mm2 copper conductor 4 core power cable

 

Sparker tester,Heating aging Chamber,High resistance machine, Oxygen index equipment, Partial ischarge inspection instruments, Fireproof testing device,High-power voltage withstand tester,No-rotor Vulkameter,Pull tester,Analytical balance,Direct current bridge,Plastic tester,Projector, Punch machine,Cross-linked cutting machine,etc.

 

 

 

 

 

 

 

 

 

About us 

Hongliang Cable Co., Ltd.
Established Year: 1988
Registered capital of RMB: 201,800,000
Total assets : 28.7millions
Factory Area: 45425 mm2
Manufacturing Capacity per year: 250000km
Number of Employees: 460

 

 

 

 

 

 

 

 

 

 

 

Packing & Shipping for  xlpe/pvc cable 4mm2 copper conductor 4 core power cable

 

 Cable should be supplied in Steel drum. Cable piece length should be of 500 meter length or as specified

by the customer at the time of order.

 

20-30 working days or as to the buyers' request .

Many transports ways at your option.

 

 

 

 

 

1. Which payment terms do you accept?
a) 30% DEPOSIT IN ADVINCE,BANLANCE AGAINST THE COPY OF B/L.
b) 100% L/C at sight.
2. What is your MOQ?
You are advised to please confirm it with us directly as it’s based on different cables.
Usually it’s 100 meters for Medium Voltage Cables.
3. What about your delivery time?
According to the order’s quantity . Usually is 15 – 30 working days.
4.How to packing the goods ?
Usually in wooden drum or steel wooden drums .The cable wire is usually coiled.
5.How to buy power cable if the type is unknown
Please tell me the application, we will help you find the type most appropriate.
6.The warranty 
Oversea technical service center 24 hous available

 

 Many thanks for your reading , if any questions please feel free to contact me.

Skype:hongliangcablesales5 

Click to  inquiry now 

 

 

 

Standard for 70mm2 Power cable

70mm2 Power cable  is manufactured according to the standard of GB12706 or IEC,BS,DIN and ICEA upon request.

 

Applications for 70mm2 Power cable

70mm2 Power cable is suitable for use in power distribution lines or fixed installations  with rated power frequency voltage up to and including  0.6/1kV

 

Operating characteristics of 70mm2 Power cable

1, Rated power-frequency voltage Uo/U : 0.6/1kV

2,Max.permissible continuous operating temperature of conductor: 90

3,Max.short-circuit temperature of the conductor shall not exceed 250.(5s maximum duration ).

4,The ambient temperature under installation should not below 0

5, The bending radius of a cable should not less than 15 times of the cable diameter.

 Production Facility for 70mm2 Power cable

 

 

 

Wendy Jiang(Sales Engineer)

SKYPE : hongliangcablesales3

TEL: 008618253153062

WELCOME TO INQUIRY !!!!!!

Send  Your Inquiry Details in the Below for Free Sample, Click "Send" now!

Brief Introduction

240mm xlpe 4 core armoured power cables are applicable for power transmission through the power line of rated voltage 1kV and below, and it is proper to lay these cables in the fixed places, such as hotels, stations, chemical engineering and oil platforms, mines, power plants, metros, and high buildings, etc.

Main products:
0.6/1kV ZR-YJV  240mm xlpe 4 core armoured power cable ;Power cable,Electrical wire cable,Below 35kV voltages of XLPE insulated cables, Armored cables, Control cables, Rubber insulated cables, PVC insulated wires and cables, BV wire,House wire,Special Cables etc.

 

Send  Your Inquiry Details in the Below for Free Sample, Click "Send" now!

Applications of 150mm2 cable

Used in electric power plants, transformer stations, industrial plants, metropolitan networks and in other electric plants where heavier current and thermal loads are expected (operating temperature of conductor up to 90℃).

Main products:
Power cable,Electrical wire cable,Below 35kV voltages of XLPE insulated cables, Armored cables, Control cables, Rubber cables, PVC insulated wires and cables, BV wire,House wire; Bare stranded conductors(AAC,ACSR,AAAC,ACAR); etc.

 

 

Packing :  150mm2 cable should be supplied in wooden drum or steel drum. 

Shipping : 20-30 working days or as to the buyers' request

 

 

Wendy Jiang(Sales Engineer)

SKYPE : hongliangcablesales3

TEL: 008618253153062

WEBSITE:  http://en.h-l.cn/en/

WELCOME TO INQUIRY !!!!!!

 

Send Your Inquiry Details in the Below for Free Sample, Click "Send" now!

Application for 4 Core Cable

Armoured Copper Power cable  is used for power transmission  and distribution  line with voltage rated at 1kV and below.Compared with PVC  Insulated Power Cable,xlpe insulated power cable boasts not  only characteristic of excellent electricity, mechanism, heat and aging-resistant, environment stress-resistant and  chemical corrosionresistant, but also  simple structure, light weight,  no restriction by laying drop,  and high temperature allowance for long term working.  

 

 

Standard of  4 Core Cable

International: IEC 60502-2

China: GB/T 12706.2-2008

Other standards such as BS,DIN and ICEA upon request

 

Technical data of 4 Core Cable 

Rated voltage: 0.6/1kV, 1.8/3kV, 6/10kV, 8.7/10kV, 8.7/15kV, 12/20kV, 21/35kV, 26/35kV

Maximum Conductor Temperature: under normal (90°C), emergency (130°C) or short circuit no more than                                                                   5 s (250°C) conditions.

Min. Ambient Temp. 0°C, after installation and only when cable is in a fixed position

Min. Bending Radius: 20 x cable O.D for single-core non-armoured cables

                                       15 x cable O.D for single-core armoured cables

                                       15 x cable O.D for multi-core non-armoured cables

 

                                       12 x cable O.D for multi-core armoured cables

 

Specification for 4 Core Cable

 

 

Picture of  4 Core Cable

    

 

 

    

Main products:
Power cable,Electrical wire cable,Below 35kV voltages of XLPE insulated cables, Armored cables, Control cables, Rubber cables, PVC insulated wires and cables, BV wire,House wire; Bare stranded conductors(AAC,ACSR,AAAC,ACAR); etc.

 

 

 

Wendy Jiang(Sales Engineer)

SKYPE : hongliangcablesales3

TEL: 008618253153062

EMAIL:wendy(at)hldlcable.com

WEBSITE:  http://en.h-l.cn

Send  Your Inquiry Details in the Below for Free Sample, Click "Send" now!

Simple specification of 4 core power cable

1)  Conductor: Cu or Al

2)  Insulation: PVC or XLPE

3)  Armour: Steel tape or Steel wire

4)  Sheath: PVC or LSZH

5)  Voltage rate:600/1000V

6)  No. of Core: 1,2,3,4,5

7)  Standard:  IEC60502,AS/NZS 5000.1

 

Standard for 4 core power cable

Power Cable is manufactured according to the standard of GB/T12706—2002 or IEC and BS and DIN and ICEA.

 

Application for 4 core power cable

Power Cable is suitable for power transmission and distribution lines with rated voltage up to including 0.6/1kV.

 

Operating characteristic for 4 core power cable

Rated power frequency voltage U0/U: 0.6/1kV

Max. admissible operating temperature of conductor : 90℃

Max. Short-circuit temperature of the conductor shall not exceeding 250℃.(Max. sustaining  period  not exceeding 5S).

The installation temperature should not be below 0℃.

The bending radius of cable should not less than 15 times.

The flame-retardant properties of cable comply with grade A ,B or C of GB/T 19666-2005

The Text Voltage(ac.): 3.5kV/5min

 

Main products:
Power cable,Electrical wire cable,Below 35kV voltages of XLPE insulated cables, Armored cables, Control cables, Rubber cables, PVC insulated wires and cables, BV wire,House wire; Bare stranded conductors(AAC,ACSR,AAAC,ACAR); etc.

 

 

 

Send  Your Inquiry Details in the Below for Free Sample, Click "Send" now!

Brief Introduction for 4 core armoured cable

underground armoured power cable is used to transmit and distribute power in power transmission and distribution system of 1kV. underground armoured power cable is generally applied to the fields including power, construction, mines, metallurgy, petrochemical industry and communication in complete replace of oil immersed paper insulated power cable and in partial replace of PVC insulated power cable.

 

 

Production Range of armoured cable:

single core cable from 2.5 mm2  to 800 mm2,muli-core cable from 2.5 mm2   to 400 mm2

 

 

Operating Characteristics:

Rated power-frequency voltage u0/u:0.6/1 KV

Max permissible continuous operating temperature of conductor 70

Max short-circuit temperature of the conductor shall not exceed (Max 5 seconds duration): cross-section of conductor  300 mm2

The ambient temperature under installations should not be below 0

The bending radius of single core cable should not be less than 20 times of the cable diameter ,the bending radius of multi-core cable should not be less than 15 times of the cable diameter.

 

Main products:
Power cable ,Electrical wire cable,Below 35kV voltages of XLPE insulated cables, Armored cables, Control cables, Rubber cables, PVC insulated wires and cables, BV wire,House wire; Bare stranded conductors(AAC,ACSR,AAAC,ACAR); etc.

 

 

 

Packing : underground armoured power cable should be supplied in steel drum.

Shipping : 20-30 working days or as to the buyers' request

 

Wendy Jiang(Sales Engineer)

SKYPE : hongliangcablesales3

TEL: 8618253153062

WELCOME TO INQUIRY!!!

Send  Your Inquiry Details in the Below for Free Sample, Click "Send" now!

Applications of  4 core power cable

Used in electric power plants, transformer stations, industrial plants, metropolitan networks and in other electric plants where heavier current and thermal loads are expected (operating temperature of conductor up to 90℃).

Main products:
Power cable,Electrical wire cable,Below 35kV voltages of XLPE insulated cables, Armored cables, Control cables, Rubber cables, PVC insulated wires and cables, BV wire,House wire; Bare stranded conductors(AAC,ACSR,AAAC,ACAR); etc.

 

Packing :  4 Core Power cable should be supplied in wooden drum or steel drum. 

Shipping : 20-30 working days or as to the buyers' request

 

 

Wendy Jiang(Sales Engineer)

SKYPE : hongliangcablesales3

TEL: 008618253153062

WEBSITE:  http://en.h-l.cn/en/

WELCOME TO INQUIRY !!!!!!

 

Send Your Inquiry Details in the Below for Free Sample, Click "Send" now!

Applications of  4 core power cable

Used in electric power plants, transformer stations, industrial plants, metropolitan networks and in other electric plants where heavier current and thermal loads are expected (operating temperature of conductor up to 90℃).

Main products:
Power cable,Electrical wire cable,Below 35kV voltages of XLPE insulated cables, Armored cables, Control cables, Rubber cables, PVC insulated wires and cables, BV wire,House wire; Bare stranded conductors(AAC,ACSR,AAAC,ACAR); etc.

 

Packing :  Power cable should be supplied in wooden drum or steel drum. 

Shipping : 20-30 working days or as to the buyers' request

Send  Your Inquiry Details in the Below for Free Sample, Click "Send" now!

Characteristics for 0.6/1kv cu/xlpe/swa/pvc power cable

Our4 core 5 core 0.6/1kv cu/xlpe/swa/pvc power cable has the advantages of not only high mechanical strength, good ambient stress resistance, good electrical properties and anti-chemical corrosion, but also simple construction, light weight and convenient to use.

 

Standards of  0.6/1kv cu/xlpe/swa/pvc power cable

Our 4 core 5 core 0.6/1kv cu/xlpe/swa/pvc power cable is manufactured in accordance with the standards of GB/T12706-2008 IEC 502. It can also be produced according to special requirements put forward by clients.

 

Operating characteristic for 0.6/1kv cu/xlpe/swa/pvc power cable

1.The highest allowed operating temperature of conductor for long-term working is 90 degrees.

2.In short circuit (Max long term is no more than 5 seconds). The highest temperature for conductor is no more than 250 degrees.

3.The cable is laid without horizontal drop limit. The environment temperature should be no lower than 0 when lay. Otherwise it should be preheated.

4.Excellent electrical performance, resistance to chemical corrosion.

5.Can stand advisable traction when laid.Can stand traction from Outside.Left low smoke halogen-free after burned.Retard the burning of the cable.

   

Specification for 0.6/1kv cu/xlpe/swa/pvc power cable 

 

 

 

 

 

 

 

 

Wendy Jiang- Sale engineer

TEL:  0086-531-88814697

FAX:  0086-531-88876156

MOB: 0086-18253153062

SKYPE:hongliangcablesales3

EMAIL: wendy(at)hldlcable.com

Send  Your Inquiry Details in the Below for Free Sample, Click "Send" now!