3 cores power cable – JYTOP Cable

3 cores power cable as IEC standard 3x25mm2 low voltage cable

admin — Fri, 27 Mar 2020 16:23:19 +0000

3 cores power cable as IEC standard 3x25mm2 low voltage cable

Product Description

What is XLPE insulated power cable?

XLPE insulated power cable has a number of advantages than paper insulted and PVC insulated cables. XLPE cable has high electric strength, mechanical strength, high-ageing resistance, environment stress resisting anti-chemical corrosion, and it is simple construction, using convenient and higher operating of long term temperature. It can be laid with no drop restriction.

XLPE cable advantages:

XLPE cable have higher long-term working temperature and greater current rating, and under the condition of the same environment, XLPE cable may be reduced size (normal cross section) 1 or 2 class in comparison with paper and PVC cable. These are not only improving the quality and properties of products, but also reduce cables' production cost.

Guowang xlpe cables standard:

Our XLPE cables can be manufactured according to company's specification which is equivalent to IEC60502, IEC60332, IEC60754, Some of indexes are superior to above international standard IEC.

Armoured Cable is divided into steel armor, fine steel wire armoured, steel wire armoring.

Steel armored cable models: VV22, VVP22, ZRVV22, NH-VV2;

Control cable with steel tape armoured cable: KVV22, KVVP2, KVVP22 model, ZR-KVV22

Steel wire armoured power cable: VV32, YJV32, ZR-VV32 model

Steel wire armored control cable type: KVV32 KVVP32

Sheathed communication cable type: HYA53, HYAT53, HYA23, HYV22, HYA22 (buried)

Steel wire armoured cable (swa armoured cable) can bear general longitudinal tensile, so it is suitable for short distance overhead or vertical installation. In foreign countries, steel wire armored cable is common used.

Low voltage SWA armoured cable construction:

-Conductor:

Solid or stranded copper

-Insulation:

Cross-linked polyethylene

-Jacket:

Polyvinyl chloride (Black)

-Standards

IEC 60502-1

-Installation:

This 0.6/1KV CU/XLPE/SWA/PVC Armoured Cable can be installed in air, duct, conduit or direct burial. It is recommended that the installation instructions indicated by the Local Electric Code, or any equivalent, so that the safeguarding of persons and the integrity of the product will not be affected by deciencies in the installation.

Detailed Picture

3 cores power cable as IEC standard 3x25mm2 low voltage cable

Application

3 cores power cable as IEC standard 3x25mm2 low voltage cable

Notes:The cables are mainly used in power stations, mass transit underground passenger systems,

airports, petrochemical plants, hotels, hospitals, and high-rise buildings.

Packaging & Shipping

Packaging: Rolls,Wooden drum or according to your request.

Ralated Products

Company Information

Our Services

Q: Are you the trading company or Manufacturer?

A: We are the manufacturer.

Q: How long does it take to get a quote back?

A: Most quotes are returned within 24 hours, however, if it is for a special construction, it could take more days.

Q: Do you custom package?

A: We strive to meet our customers' needs and therefore have no problem meeting most specifications. We can reel into coils, disposable cartons, special reels, or load your wire and cable into reusable plastic containers. Please check with your sales representative first to verify we can meet your need.

Q: Do you offer free samples?

A: Yes, we can offer free samples, but freight collect.

Q: How long is your warranty period?

A: Guowang cable guarantees that all of our products, wires and cables, are free from defects. We will take back any product that does not meet the agreed quality by both parties. The warranty shall remain valid for twelve (12) months after the Goods, or any portion thereof as the case maybe, have been delivered to and accepted at the final destination indicated in the SCC, or for eighteen (18) months after the date of shipment from the port or place of loading in the country of origin, whichever period concludes earlier.

Top Quality Solid 3 Cores PVC Insulated Copper Wire Electric Power Cable Wire

admin — Mon, 21 Oct 2019 13:13:05 +0000

Top Quality Solid 3 Cores PVC Insulated Copper Wire Electric Power Cable Wire

Product Description

Polyvinyl chloride insulated cables and cords of rated voltages up to and including 450/750V

Application

Wiring for electrical appliances, smaller size electric tools, instruments of various meters, and motorized lighting system.

Standard

IEC 60227,IEC 60228,IEC 60332,GB/T 5023,BS 6500,BS 6004,VDE 0281,0282 , EN 50525-1, AS/NZS 5000.2 etc.

*Hongda Cable can also design and produce for special application requirement.

Type and description

Serial number	Type	Description
1	60227 IEC 01(BV) (H07V-U or H07V-R)	Single core solid or stranded conductor unsheathed cable for general purposes
2	60227 IEC 02(RV) (H07V-K)	Single core flexible conductor unsheathed cable for general purposes
3	60227 IEC 05(BV) (H05V-U or H05V-R)	Single core 70℃ solid or stranded conductor unsheathed cable for internal wiring
4	60227 IEC 06(RV) (H05V-K)	Single core 70℃ flexible conductor unsheathed cable for internal wiring
5	60227 IEC 07(BV-90) (H07V2-U or H07V2-R)	Single core 90℃ solid conductor unsheathed cable for internal wiring
6	60227 IEC 08(RV-90) (H07V2-K)	Single core 90℃ flexible conductor unsheathed cable for internal wiring
7	60227 IEC 10(BVV) (NYY or NYM)	Light PVC sheathed cable
8	60227 IEC 42(RVB)	Flat unsheathed flexible wire
9	60227 IEC 52(RVV) (H03VV-F,H03VV2-F)	Light PVC sheathed flexible wire
10	60227 IEC 53(RVV) (H05VV-F,H05VV2-F)	Common PVC sheathed flexible wire
11	BV (H07V-U or H07V-R)	Copper conductor PVC insulated wire
12	BLV	Aluminum conductor PVC insulated wire
13	BVR	Copper conductor PVC insulated flexible cable
14	BVV (NYY or NYM)	Copper conductor PVC insulated sheathed circular cable
15	BLVV	Aluminum conductor PVC insulated and sheathed round cable
16	BVVB (H05VVH2-F)	Copper conductor PVC insulated and sheathed flat cable
17	BLVVB	Aluminum conductor PVC insulated sheathed flat cable
18	NMD-90	Copper conductor PVC/Nylon Insulated PVC Jacked flat cable
19	RVS	Twisted copper conductor PVC insulated flexible cable for conection
20	AVP	Copper conductor PVC insulated wire with shied for installation
21	RVP	Copper conductor PVC insulated flexible wire with shield
22	RVVP	Copper conductor PVC insulated, shielded, PVC sheathed flexible cable

NOTE:1) Cores number series ar,1,2 ,3,4and 5.

2) HONGDA CABLE can produce “Flame-Retardant Series”, “Fire-Resistant Series”, “Low Smoke Halogen Free (LSHF/LSOH) Series”, “Low Smoke Low Halogen (LSLH) Series”, etc.

Performance in line with IEC60332,IEC 61034,IEC60754 requirements.

Packaging & Shipping

Packing:

Steel wooden drum (fumigation)

Cable length in each drum: 1000m/2000m or as per actual cable length requirements.

Drum size:

As per cable length and container size

*In order to quote you accurate price, kindly tell us your needed cable length quantity. Larger quantity, more discount benefit ready for you!

Shipping Port:

Shanghai, Qingdao, Tianjin or other ports as per your requirements.

Sea freight:

FOB/C&F/CIF/DAP quotation are all available.

Company Information

Zhengzhou Hongda Cable Co., Ltd as the leading company of producing electrical power cable, was established

in March 1999. Our company covers an area of 100,000 square meters, has more than 120 members and professional workers.

We Specialized in Low Voltage XLPE insulated power cable, PVC insulated power cable, Control cable;Bare Conductor (AAC AAAC ACSR),Overhead Insulated Cable,PVC Insulated Wire up to 450/750V,PVC insulated flexible wire.

All products can meet GB,IEC,NEMA,JIS ,BS,and other relevant standards .We also can produce products based on customers' requirements.

To meet customers' needs and exceed customers' expectations is our perpetual goal. Zhengzhou Hongda Cable Co., Ltd.sincerely welcomes your inquiry!

Certifications

FAQ

1. Is your company a factory or trading company?

We are factory with our own trading company. Our trade business expands home and abroad.

2. When can I get the price?

We usually quote within 12 hours after we get your inquiry. If you are very urgent to get the price, please call us or tell us in your e-mail so that we will regard your inquiry priority.

3. How can I get a sample to check your quality?

After price confirmation, you can require for samples to check our quality. Sample is free, but the freight charge should be paid.

4. What is Minimum Order Quantity?

Generally, 1000 meters for building wire. For power cable, armored or unarmored, 500 meters.

5. Which standards for your products?

We can produce wire and cable according to international standards: IEC, ASTM, BS, DIN, SANS, CSA or as customers’ requirement.

6. How about delivery time?

If we have stock, delivery would be very quick. For the newly-produced products, 15 to 25 days for production.

7. Payment terms:

Normally 30% paid as prepayment, balance paid before delivery. Or 100% L/C at sight.

8. What is your packing?

Our electrical cable is using electrical cable wheel for the packing, the wheel can be all steel, steel frame and fumigated wood, or fumigated wooden cases. We are using different packing for different length of the cable, to ensure there will be no problem during the delivery of the products.

Customer reviews

Combination of production and trade

Any needs or question, please contact Shawn:

24kV 3 cores CU / XLPE / PVC / DSTA / PVC xlpe insulated power cable

admin — Thu, 05 Sep 2019 11:46:52 +0000

24kV 3 cores CU / XLPE / PVC / DSTA / PVC xlpe insulated power cable

Product Description

1. CU / XLPE / PVC / DSTA / PVC Use:

The three core cables are designed for distribution of electrical power with nominal voltage Uo/U ranging from 3.6/6.6KV to 19/33KV and frequency 50Hz. They are suitable for installation mostly in power supply stations, indoors and in cable ducts, outdoors, underground and in water as well as for installation on cable trays for industries, switchboards and power stations.

2. CU / XLPE / PVC / DSTA / PVC Standards:

This product is manufactured according to GB/T12706, equivalent to IEC60502 or BS, DIN, ICEA standard as to customer’s requests.
D.C Resistance of the conductor complies with the stipulations of GB/T3956.
Flame-retardant properties of the cable comply with Grade A, B and C of GB/T19666-2005, equivalent to IEC60332.

3. CU / XLPE / PVC / DSTA / PVC Voltage Test and Partial Discharge Test

Nominal /Operating /Test Voltages

Rated Voltage Uo/U	Operating Voltage (Um)	Testing Voltage (rms)
3.8/6.6KV	7.2KV	15KV
6.35/11KV	12KV	25.5KV
8.7/15KV	17.5KV	35KV
12.7/22KV	24KV	51KV
19/33KV	36KV	76KV

4. CU / XLPE / PVC / DSTA / PVC structure

Conductor	Plain annealed copper or aluminium complying with IEC 60228/BS 6360. Copper conductors shall be stranded (class 2) and aluminium conductors shall be either solid or stranded (class 2).
Conductor Screen	Extruded layer of semi-conducting cross-linkable compound is applied over the conductor and shall cover the surface completely. The minimum thickness is 0.3mm and the maximum resistivity shall not exceed 500 Ohm-m at 90°C.
Insulation	Insulation is of cross-linked polyethylene compound XLPE (GP8) conforming to BS 7655-1.3 or EPR (GP7), conforming to BS 7655-1.2.
Insulaton Screen	Extruded layer of semi-conducting cross-linkable compound is applied over the insulation. The extruded semi-conducting layer shall consist of bonded or cold strippable semi-conducting compound capable of removal for jointing or terminating. As an option, a semi-conducting tape may be applied over the extruded semi-conducting layer as a bedding for the metallic layer. The minimum thickness is 0.3 mm and the maximum resistivity is 500 Ohm-m at 90°C. The screen is tightly fitted to the insulation to exclude all air voids and can be easily hand stripped on site.
Inner Covering & Fillers	For cables with a collective metallic layer or cables with a metallic layer over each individual cores with additional collective metallic layers, semi-conducting inner covering and fillers shall be applied over the laid up cores. The inner covering is made of non hygroscopic material, except if the cable is to be made longitudinally watertight. The inner covering shall be extruded or lapped.
Metallic Layer	The metallic layer shall be applied over each core or applied as a collective screen. The metallic screen shall consist of either copper tapes or a concentric layer of copper wires or a combination of tapes and wires. The metallic layer provides an earth fault current path, capable of withstanding fault current to earth of 1000A for one second at maximum temperature 160°C. Copper wires are applied over the conducting water blocking layer with a minimum diameter of 0.5mm. And over the copper wires, copper tape with minimum thickness of 0.1mm can be applied helically with overlap.
Separation Sheath (for armoured cable)	The separation sheath comprises a layer of extruded PVC, PE or LSZH. The nominal thickness is calculated by 0.02Du + 0.6mm where Du is the fictitious diameter under the sheath in mm. The nominal separation sheath thickness shall not be less than 1.2mm.
Armour (for armoured cable)	The armour consists of galvanized steel wire applied over the inner covering with diameter.
Over Sheath	Overall sheath comprises a layer of extruded either PVC type 9 conforming to BS 7665-4.2 or MDPE type TS2 conforming to BS 7655-10.1; LSZH can be offered as an option. The over sheath is normally black in colour. When a DC voltage test is to be performed on the over sheath, a semi-conducting layer such as graphite coating shall be applied over the surface of the extruded over sheath. The nominal over sheath thickness is calculated by 0.035+D where D is the diameter immediately under the over sheath in mm. For cables with the over sheath not applied over the armour, the nominal over sheath thickness shall not be less than 1.4mm. And for cables with over sheath applied over the armour, the nominal over sheath thickness shall not be less than 1.8mm.

CU / XLPE / PVC / DSTA / PVC PHYSICAL PROPERTIES

Operating Temperature	up to 90°C
Temperature Range	-5°C ( PVC or LSZH sheath ); -20°C ( PE sheath )
Short Circuit Temperature	250°C (short circuit duration up to 5 seconds)
Bending Radius	15 x OD

5. Product Description for CU / XLPE / PVC / DSTA / PVC :

CU / XLPE / PVC / DSTA / PVC Reference Standards:	IEC60502-2, IEC 60228, IEC60332 -1/2/3, BS6622, BS7835, VDE0276, AS/NZS 1429.1, GB/T 12706, etc.
Rated Voltage:	6/10kV, 6.35/11kV (12kV), 8.7/15kV, 12/20kV, 18/30kV,19/33kV
Core Number:	Single Core or Three Core (1C or 3C)
Available Dimensions:	25mm2, 35mm2, 50mm2, 70mm2, 95mm2, 120mm2, 150mm2, 185mm2, 240mm2, 300mm2, 400mm2, 500mm2, 630mm2.
Codes Available:	N2XSY, N2XSEY, NA2XSY, NA2XSEY, N2XSRY, NA2XSRY, N2XSEBY, N2XSEYBY, NA2XSEBY, N2XSERY, NA2XSERY, N2XSEYRGbY, NA2XSEYRGbY, N2XS(F)2Y, NA 2XS(F)2Y, N2XS(FL)2Y, N2XSH, N2XSYRY
Codes Available:	YJV, YJLV, YJSV, YJLSV, YJV72, YJLV72, YJSV72, YJLSV72, YJV22, YJLV22, YJSV22, YJLSV22, YJV32, YJLV32, YJSV32, YJLSV32
Application:	For power networks, underground, outdoors and in cable ducting. It is recommended that the installation instructions indicated by the Local Electric Code, or any equivalent, be followed, so that the safeguarding of persons and the integrity of the product will not be affected during installation.
CU / XLPE / PVC / DSTA / PVC Construction:
Conductor:	Stranded round compacted copper or aluminum conductor (Cu / Al ), copper wire annealed.
Conductor Screen:	Semi-conducting material
Insulation:	XLPE (Cross-Linked Polyethylene)
Insulation Screen:	Semi-conducting material
Metallic Screen:	Copper tape screen or copper wire screen (CTS / CWS )
Filler:	PP rope
Separator:	Binding tape
Bedding:	PVC (Polyvinyl Chloride)
Armouring:	Single Core: Aluminium Wire Armoured (AWA) Multi-core: Steel Wire Armoured (SWA) or Steel Tape Armoured (STA)
Sheath:	PVC (Polyvinyl Chloride), flame retardant PVC, PE, LSOH, HFFR
Colour:	Red or Black
Temperature Rating:	0°C to 90°C
Minimum Bending Radius:	Single Core: 15 x overall diameter Three Core: 12 x overall diameter (Single Core 12 x overall diameter and 3 core 10 x overall diameter where bands are positioned adjacent to joint or terminations provided that the bending is carefully controlled by the use of a former)

6. CU / XLPE / PVC / DSTA / PVC Models

Model	Voltage	Name	Standards
YJV YJLV	3.6/6kV 6/6kV 6/10kV 8.7/10kV 8.7/15kV 12/20kV 18/30kV 21/35kV 26/35kV	Copper (Aluminum) conductor XLPE insulated PVC sheath power cable	IEC60502-1 GB/T 12706
YJV22 YJLV22		Copper (Aluminum) conductor XLPE insulated Steel tape armored PVC sheath power cable
YJV62 YJLV62		Copper (Aluminum) conductor XLPE insulated Non-magnet steel tape armored PVC sheath power cable
ZA(B, C)-YJV ZA(B, C)-YJLV		Copper (Aluminum) conductor XLPE insulated PVC sheath flame-retardant power cable
ZA(B, C)-YJV22 ZA(B, C)-YJLV22		Copper (Aluminum) conductor XLPE insulated Steel tape armored PVC sheath flame-retardant power cable
ZA(B, C)-YJV62 ZA(B, C)-YJLV62		Copper (Aluminum) conductor XLPE insulated Non-magnet steel tape armored PVC sheath flame-retardant power cable
WDZ-YJY		Copper conductor XLPE insulated LSHF power cable
WDZ-YJY23		Copper conductor XLPE insulated Steel tape armored LSHF power cable
WDZ-YJY63		Copper conductor XLPE insulated Non-magnet steel tape armored LSHF power cable

Notes:

1. Non-magnet steel tape armored is used for single core cable. Figure 6 in the models means “armored”.

2. Flame-retardant grades are A, B and C, which can be chosen according to requirements.

Packaging & Shipping

CU / XLPE / PVC / DSTA / PVC Packaging & shipping

Packaging

Packaging available on 500 or 1000 metres
Wooden & steel drums

Shipping:
Port: Tianjin, Qingdao, Shanghai or other ports as per your requirements.

Sea freight:
FOB/C&F/CIF/DDU quotation are all available.

Our Services

Our service

we are one of the biggest manufacture in china mainland. We will give you a perfect shopping experience . If you need visit our factory , we will meet you at the airport or train station.

Also we can offer other service

Custom Merchandise:we can make cable as your need include the color ,size and so on.we also offer OEM .

Complete Course Tracking:we can offer you the service from the business begin to you get the cable and use it .

Company Information

Company information

Cable sample: we can offer the sample free .

Zhengzhou hongda cable Co., Ltd.
Established Year:1999
Registered capital of RMB:5,000,000
Factory Area:300,000m2

Main products:

Areial bundle cable ,XLPE insulated power cable ,PVC insulated power cable ,electrical wire ,bare aluminum conductor(AAC AAAC ACSR )and so on

Main export county:

USA Philippines Malaysia Indonesia Venezuela, Colombia Mexico

Dominica India South Africa Zambia Kenya and so on .

Why Choose Us

1. We have a large production base, and advanced production equipment
2. Have an competitive price and high quality
3. Excellent after-sale service
4. Attractive design and various styles
5. Free issue:packaging list,invoice,CD installation
6. Powerful technology R&D team
7. Strict quality assurance system and perfect testing means
8. Advanced process equipment
9. Painted with powerful antiseptic Anticorrosion material paints
10. Delivery on time
11. Our roller coaster sales to Middle East,Africa,Russia,Southeast Asia, etc.
12.We have a good reputation in the overseas

Contact Information

CU / XLPE / PVC / DSTA / PVC Contact information

Any needs or question ,please contact us ,we will be more pleasure to service you.

Skype ID: xinyuanyy
Cellphone/WhatsApp/Wechat/ICQ: +86 158 3829 0725

Facebook: xin.yuan.73307

We are looking forward to your inquiry and nice cooperaton.

Medium voltage armor cable xlpe insulation 11kv 3 cores power cable price

admin — Tue, 27 Aug 2019 17:18:02 +0000

3 core 11 kv 120mm2 150mm2 medium voltage power cable

TOP TEN CABLE MANUFACTURER/EXPORTER IN CHINA
LARGEST CABLE MANUFACTUER IN NORTH CHINA
ANNUAL EXPORT VOLUME EXCEED 200MILLION USD
WITH UL,TUV,KEMA,CE,BV,PSB,SABS,LLOYD'S,GL,NK,KR,ABS PRODUCTS CERTIFICATIONS
WITH TUV TYPE TESTING REPORT
WIDE PRODUCTS RANGE
ISO9001,ISO18001,OHSAS18001 SYSTEM CERTIFICATIONS
CNAS APPROVAL LABROTARY

Standard:IEC60502, BS6346, VDE, AS/NZS, UL,etc

The Rated Voltage(kv):

1st class 0.6/1 1.8/3 3.6/6 6/10 8.7/15 12/20 18/30 21/35
2nd class 1/1 3/3 6/6 8.7/10 12/15 18/20 – 26/35

Number of cores:

1, 2, 3, 3+1, 3+2, 3+3, 4, 4+1, 4+2, 5 low votage

1 or 3 core medium voltage

Construction:

Conductor: Solid or stranded copper/aluminum

Insulation: Cross-linked polyethylene (XLPE)

Filler: Polypropylene filament with lapped binding tape
Binder: Binding tape
Inner sheath: Polyvinyl chloride (PVC)
Amour: Galvanized steel wire armored(SWA) or steel tape armored(STA)
Sheath: Polyvinyl chloride (PVC)

Sectional Area:

1.5 mm2 , 2.5 mm2 ,4 mm2 , 6 mm2 , 10 mm2 , 16 mm2 ,25 mm2 , 35 mm2 , 50 mm2 ,70 mm2 , 95 mm2 ,120 mm2 ,150 mm2 ,185 mm2 ,240 mm2 ,300 mm2 400 mm2 500 mm2 630 mm2 800 mm2

production range: single core cable from 1.5 mm2 to 800 mm2,muli-core cable from 1.5 mm2 to 400 mm2

Type and Name:

Model		Name	Application	Cable Cores	Section area (mm)
Copper Core	Aluminum Core	Name	Application	Cable Cores	Section area (mm)
YJV	YJLV	CU/AL Conductor, XLPE Insulated, PVC Sheathed Power Cable	XLPE insulation PVC/PE sheathed power cables are used for laying indoors and outdoors. Able to bear certain traction during installation, but not external mechanical forces and pulling forces. Single core cable can't laying in magnetic ducts .	1C 3C	25 \| 400
YJY	YJLY	CU/AL Conductor, XLPE Insulated, PE Sheathed Power Cable
YJV22	YJLV22	CU/AL Conductor, XLPE Insulated,Steel-Tape Armored,PVC Sheathed Power Cable	XLPE insulation PVC/PE sheathed steel-tape armored power cables can be buried directly .Able to bear external mechanical forces but large pulling forces.
YJV23	YJLV23	CU/AL Conductor, XLPE Insulated,Steel-Tape Armored,PVC Sheathed Power Cable
YJV32	YJLV32	CU/AL Conductor, XLPE Insulated,Thin Steel-Wire Armored,PVC Sheathed Power Cable	XLPE insulation armoured power cables can apply to shafts,water and soil. Able to bear moderate pulling forces.
YJV33	YJLV33	CU/AL Conductor, XLPE Insulated,Thin Steel-Wire Armored,PE Sheathed Power Cable
YJV42	YJLV42	CU/AL Conductor, XLPE Insulated,Thick Steel-Wire Armored,PVC Sheathed Power Cable	Steel-wire armored,PVC/PE Sheathed Power Cables are apply to shafts,water and soil.Able to bear large pulling forces.
YJV43	YJLV43	CU/AL Conductor, XLPE Insulated,Thick Steel-Wire Armored,PE Sheathed Power Cable

Packaging & Shipping

UL certificate

We are one of China top rank cable&wire manufacturer.Our products meet standards of GB, IEC DIN ASTM, JIS, NF, AS/NZS CSA GOST and so on. We also have obtained ISO9001,ISO14001,OHSAS18001, UL,CE,

KEMA, TUV, SABS,PBS,Bureau Veritas, Lloyd,GL,NK,KR certifications.

We have obtained UL certifications for TC cable, DLO cable,RHH/RHW/RHW-2,XHHW/XHHW-2/SIS, THHN,SER/SEU/USE, MV-90/MV-105,MC cable,AC cable,TECK 90,SOOW,Welding cable,Mining cable,type DG,PV cable,Shipboard cable and so on.

Company Information

Hebei Huatong Wires and Cables Group Co., Ltd was established in 1993, covering an area of 230, 000 square meters. We own more than 420 sets manufacturing equipment and 250 sets of testing equipment or apparatus. Our annual production capacity is 5 billion Yuan.We have 1200 employers, among which 150 are technicians. Based on the scientific management, now we are a comprehensive, large-scale enterprises in wire and cable industry.Voltage up to 35KV, including X L P E power cables,PVC power cables, mining cables, rubber cables for general purpose, Submersible oil pump cables, solar cables, shipboard cables,lead sheath cables, aerial cables, control and instrument cables, special cables etc.Products are exported to USA, Australia, Singapore, Europe, South America, Middle East, Asia, Africa. CNAS accredited national level laboratory.

Laboratory

CNAS accredited national level laboratory.

Our Services

1.25 years production experience and 16 years export experience .
2.Products certification :UL,CE,BV,TUV,KEMA,PSB,SABS,ABS,NK,LR,KR,GL etc
3. OEM service available based on official & legal authorization.
4.Strict quality control system.
5.Rapid delivery and feedback Faster lead time than our competitors.
6.Excellent quality with reasonable price.
7.Strong technical support (technical data, drawing, etc.)
8.Professional teamwork service for you actively.
9.Stock available, Free sample is available.

FAQ

(1).When can I get the price?
We usually quote within 6 hours after we get your inquiry. If you are very urgent to get the price,please call us or tell us in your e-mail so that we will regard your inquiry priority.

(2).How can I get a sample to check your quality?
After price confirmation, you can require for samples to check our quality. Sample is free, but the freight charge should be paid.

(3).How long can I expect to get the sample?
After you pay the freight charge and send us confirmed files, the samples will be ready for delivery in 3-7 days. The samples will be sent to you via express and arrive in 3~5 days. You can use your own express account or prepay us if you do not have an account.

(4).What about the lead time for mass production?
Honestly, it depends on the order quantity and the season you place the order.The best record we keep is delivering 10 kilometers cable within a week. Generally speaking, we suggest that you start inquiry two months before the date you would like to get the products at your country.